FB Factorio Blueprints

Hub Extender

Anonymous

The purpose of the hub extender is to give the player the hub experience (being supplied and have the trash removed) even while being on the other side of the map. The Hub extender consists of two parts: A Producer station and one or many customer stations. The provider station has to be placed within the logistic network of the hub. The customer stations can be placed all around the map, except within the logistic network of the hub (which would defeat the purpose of the extender anyway). # Requirements * You need a train grid, which connects all customer stations with the provider station (obviously) * There has to be a circuit network of both red and green wire alongside the train grid, which all stations will be connected to * I'm using Factorio 1.1 # Mods There are no mods required for the funtion of the blueprints. I used the nixie-tubes and textplates mod to get some structure and visualization. I included the blueprints with and without the mod parts. # Provider station To set up the provider station: * Place it down somewhere within the logistic network of your hub * Connect the lone medium powerpole on the left side with the arrows surrounding it to the circuit grid. Both red and green circuit are needed. With those two steps the provider is already functional. # Customer station(s) To set up the customer station: * Place it down anywhere on the map on the same train grid as the provider station * Set the ID of the customer station. More information bellow. * Rename the station to, for example: Customer #ID * Give the train some fuel and set it to automatic. * Connect the green and red circuit to the grid. With this the setup of the customer is done. You can now set your item requests with the constant combinators near the bottom half of the customer station. The blueprint already has the request for some robots added to the blueprint. It is important to let the train go once before setting to many requests in order for it to fetch some logistic robots. And that's it. If you have done all the above then it is up and running and you can start requesting items from the hub and have your trash from the inventory transported back to the hub. ### Customer ID The Customer ID is the virtual Signal "C" within the constant combinator near the top of the customer station, surrounded by arrows. The ID has to start with 1 and additional customer stations have to be increments of 1. Example: The IDs "C1", "C2", C3" are the IDs for each station respectively when using 3 customers. It cannot be "C1", C3" and "C5". The provider station will notice the ID conflict and produce an error. It will stop operating until the conflict is solved and then start working again. # How it works ## The circuit grid In order to transmit the requests from the customers to the provider communication between them is required. It uses the circuit grid between all customers and the provider to do so. ### Red wire The red circuit is used as the command channel. Only the provider station sends commands to it. In order to allow other services, which you might have, to use the red and green circuit as well a locking virtual signal will be send. Everytime the producer station sends a command it will also send the "L1" signal. If there already is a "L" signal on the red wire, then the provider station will not send any commands and wait. ### Green wire The green wire is the response channel. Only the customer stations send information over it and they only do so when they receive a request from the provider station. ## Workflow 1. The provider station sends a request to all customers. (Signal: "C-1"). Every customer answers with "C1" and their ID converted to the signal "S". So in case of 3 customers, the provider receives: C3 + S6. The S signal allows the detection of ID errors. 2. The provider iterates over all known customers, starting from the first 3. - The provider sends the Info signal + the customer ID and the receiving customer station answers with its list of requested items. Trash items (items to send back to the hub) are represented by the virtual signal "G" 4. - If the provider receives item requests, then it sends the "check" signal to the customer, which will then send out it's train. As soon as the provider receives the "check" signal in return from the customer, it will set the item requests via it's request chests. 5. - The customer train arrives and gets unloaded first and loaded with all items afterwards. After it has finished loading it will return to the customer station 6. - The provider now asks the next customer in line 7. After all customers are processed it will start at step 1 again